エラーコード一覧¶
Command Code¶
Command Code |
メッセージ内容 |
---|---|
0x01 |
Set Reader Power Control |
0x03 |
Get Reader Information |
0x06 |
Get Region |
0x07 |
Set Region |
0x08 |
Set System Reset |
0x0B |
Get Type C A/I Select Parameters |
0x0C |
Set Type C A/I Select Parameters |
0x0D |
Get Type C A/I Query Related Parameters |
0x0E |
Set Type C A/I Query Related Parameters |
0x11 |
Get current RF Channel |
0x12 |
Set current RF Channel |
0x13 |
Get FH and LBT Parameters |
0x14 |
Set FH and LBT Parameters |
0x15 |
Get Tx Power Level |
0x16 |
Set Tx Power Level |
0x17 |
RF CW signal control |
0x22 |
Read Type C UII |
0x23 |
Read Type C UII RSSI |
0x25 |
Read Type C UII TID |
0x29 |
Read Type C Tag Data |
0x2A |
Read Type C Tag Long Data |
0x2E |
Get Session |
0x2F |
Set Session |
0x30 |
Get Frequency Hopping Table |
0x31 |
Set Frequency Hopping Table |
0x32 |
Get Modulation |
0x33 |
Set Modulation |
0x34 |
Get Anti-Collision Mode |
0x35 |
Set Anti-Collision Mode |
0x36 |
Start Auto Read2 |
0x37 |
Stop Auto Read2 |
0x38 |
Start Auto Read RSSI |
0x39 |
Stop Auto Read RSSI |
0x46 |
Write Type C Tag Data |
0x47 |
BlockWrite Type C Tag Data |
0x48 |
BlockErase Type C Tag Data |
0x83 |
BlockPermalock Type C Tag |
0x65 |
Kill/Recom Type C Tag |
0x82 |
Lock Type C Tag |
0xAC |
Antenna Check |
0xC5 |
Get RSSI |
0xC6 |
Scan RSSI |
0xCA |
Get DTC Result |
0xD2 |
Update Registry |
0xD4 |
Get Registry Item |
0xFF |
Command Failure |
0xE4 |
Set Optimum Frequency Hopping Table |
0xE5 |
Get Frequency Hopping Mode |
0xE6 |
Set Frequency Hopping Mode |
0xE7 |
Get Tx Leakage RSSI Level for Smart hopping Mode |
0xE8 |
Set Tx Leakage RSSI Level for Smart hopping Mode |
0xEC |
Start Read with Fast Leakage Cal. |
0xED |
Request Fast Leakage Cal. |
Sub Error Code for RFID¶
対応モデル:ASR-030D、ASR-031D、ASR-0230D、ASR-0231D、ASR-0240D、ASR-L70D、ASR-M30S
Sub Error Code |
内容 |
---|---|
0x01 |
Not supported |
0x02 |
Insufficient privileges |
0x03 |
Memory overrun |
0x04 |
Memory locked |
0x05 |
Crypto suite error |
0x06 |
Command not encapsulated |
0x07 |
ResponseBuffer overflow |
0x08 |
Security timeout |
0x0B |
Insufficient power |
0x0F |
Non-specific error |
0x11 |
Sensor Scheduling configuration |
0x12 |
Tag Busy |
0x13 |
Measurement type not supported |
0x80 |
No tag detected |
0x81 |
Handle acquisition failure |
0x82 |
Access password failure |
0x90 |
CRC error |
0x91 |
Rx Timeout |
0xA0 |
Registry update failure |
0xA1 |
Registry erase failure |
0xA2 |
Registry write failure |
0xA3 |
Registry not exist |
0xB0 |
UART failure |
0xB1 |
SPI failure |
0xB2 |
I2C failure |
0xB3 |
GPIO failure |
0xE0 |
Not supported command |
0xE1 |
Undefined command |
0xE2 |
Invalid parameter |
0xE3 |
Too high parameter |
0xE4 |
Too low parameter |
0xE5 |
Failure automatic read operation |
0xE6 |
Not automatic read mode |
0xE7 |
Failure to get last response |
0xE8 |
Failure to control test |
0xE9 |
Failure to reset Reader |
0xEA |
Rfidblock control failure |
0xEB |
Automatic read in operation |
0xF0 |
Undefined other error |
0xF1 |
Failure to verify write operation |
0xFC |
Abnormal antenna |
0xFF |
None error |
Sub Error Code for Barcode¶
対応モデル:ASX-300R、ASX-301R、ASX-510R、ASX-520R、ASR-010D、ASR-020D、ASR-022D、ASR-0230D、ASR-0231D、ASR-0240D
Sub Error Code |
内容 |
---|---|
0xE0 |
ERR_NOT SUPRT_CMD |
0x0E |
ERR_INVALID_PARM |
0x17 |
FAIL_NOT_SUPRT_CMD |
0x18 |
FAIL_UNDEF_CMD |
0x01 |
FAIL_RDR_PWR_CTRL |
0xE9 |
FAIL_RDR_ALREADY_PWR_ON |
0xFF |
FAIL_CRC_ERROR |
Sub Error Code for M24D¶
対応モデル:ASR-M24D
Sub Error Code |
内容 |
---|---|
0x17 |
Not Support Command |
0x18 |
Undefined Command |
0x01 |
Reader Power Control Fail |
0x0E |
Invalid Parameter |
0x0A |
Auto Read Fail |
0xE9 |
Reader Already Power On |
0xFF |
CRC check Error |
0x20 |
Barcode SSI Timeout |
0x21 |
Barcode SSI No Ack |
0x80 |
NV item Write Fail |
0x81 |
NV item Write Fail (Battery Low Voltage) |
0x82 |
NV item erase Fail |
0xE5 |
Auto Read in Operation Fail |